EUR
en
Approx 126 hours, 6” submersible pump, 66” wide cutterhead. Dimensions/weight: 22’L x 6’W x 6’H, 4000 lbs. Floating discharge package (200’ floating pipline with locking clamps), 20 pcs HDPE discharge pipe assembly 20’ each, 20 eccentric clamps, travel package (cable rigging components), trailer with pipe rack, cutterhead wheel kitPrice:$130,000
Built 2009, Cat C7 engine (7000 total hours on engine, approx 2500 on rebuild), (trailer included), 4800’ dredge pipe (approx 1500’ 8”, 3300’ 10”), 31 floats, skid mounted Metso 8” x 8” booster pump with Cat 3306Package Price: $585,000
42.8’L x 18.5’W, 17.5’ depth, 42,000 lb overall weight, 19.5” impeller dredge pump, 25 hp cutter power, cylinder ladder lift/swing, 8” square spud, articulating rear spud, Cat 275 hp diesel engine, inline direct marine style transmission for dredge pump reduction, PLC operating system, standard equipment, power up/down winches for proper cable storage, stern kicker spud or extending leg for controlled positioning, located FloridaPrice: $300,000
42.8’L x 18.5’W, 17.5’ dredging depth, 42,000 lb overall weight, 19.5” impeller dredge pump, located Midwest USPrice: $240,000
15’ depth. 32’ length. Detroit 6 cylinder. 8” discharge. Cutter head width: 98". Capacity: 2000 gallons per minute. Thomas pump. Replaced main gear box – rebuilt box $30k, includes 1500’ of 8” dredge pipe, fittings, floats and (2) 8” hoses, located PennsylvaniaPrice:$80,000
Used on one job, very good condition. (it was attached to a Cat 336 long reach excavator to dredge 50’).Price: $90,000
Detroit diesel engine, 3826 hours, secondary hour meter reading 985, boom, mud shield, enclosed cab, winch, 108” wide, auger, toolboxes (no trailer)Price on Request
Built 2003, 20’ max dredge depth, 102” cutterhead width, 18000 lbs, 32.5’ long x 8.5’ beam x 27” draft, steel pontoons, new 275 John Deere diesel engine (rebuilt 2024 with 1200 hours), 150 cu yard/hour pumps, 2000 gal/minute, enclosed cab, reverse, used in fresh water only, 368’ of 6” hard pipe, 1000’ flex pipe, trailer not included, located New YorkPrice: $315,000
Built 2020, used very little (less than one week), 15’ working depth, 8’ cut width, 17” cut height, 22.5” avg draft, Catamaran hull type, John Deere 125 hp engine, 60 gal fuel capacity, MudCat slurry pump with 8” discharge, 3000 gpm max performance, 3.5” solids passage (closed impeller), 4.3” solids passage (open impeller)Price: $210,000
CAT 336 LONG REACH EXCAVATOR, standard arm, 48” bucket, long reach arm 42” bucket, open/close hydraulics both arms, includes 65’ long reach arm, 4400 hoursPrice: $295,000
Available at extra cost:
10’ Steel extension (fits standard arm for 10’ more reach) new 2022- $10,000
Kinshover YC600 1.2 cu yd clamshell bucket, reinforced-15,000
Teran Grapple (fits long reach) new 2023-$8,300
Underwater camera, installed on long reach new 2023 - $2,500
8” HDPE SDR17 dredge pipe (2040’) flanged and bolted, new 2023 - $26,000
8” HDPE (350’) flagged, bolted, new 2023 - $8,500
6” HDPE SDR11 dredge pipe, flanged, new 2022 - $17,000
6” hose, 700’ flanged (35 pieces 20’ long) 250 psi high pressure $26,000
8” flex hose, (3) 25’ pieces, flanged, new 2023 - $10,500
8” bell pump, cutterhead (attaches to excavator) new 2023 – $80,000
10” pipe floats, 10, new 2023 - $8,850
10” pipe floats, 9, used $5,750
8” pipe floats, 12, new 2023 - $27,000
6300 Hp 160’ Cargo/Crew/Project Support Vessel, Built 2002 – $950,000
Built 1994, 10’ dredging depth, 6” open faced slurry pump, 6” discharge, up to 2400 gpm water and 800 to 1200 gpm thick slurry pumping, pump distance ¾ mile at 1000 gpm, located CaliforniaPrice: $45,000
Manufactured 2005, 2500 hours, 20’ depth, 24” x 96” auger, 8” submersible pump, can produce 228 gpm @ 140’ head, Cat 275 hp diesel engine, New York Price: $75,000
8” discharge, 7’ cutter on 21’ elevator (part that moves while cutting), will produce one yard a minute in sandy/silty (not heavy rock) material and will push out at zero elevation 2100’, 2023 Twin 90 hp Yamaha engine, 8’ custom built self-propelled, enclosed cab, with 30’ gooseneck trailer, located Georgia Price: $125,000
25’ ladder length, 66’l x 17’10”w (with side tanks), 4’ depth, 10’ height (spuds removed), 30” mean draft (with fuel), 10” spud length, digging depth 2’ – 19’, maximum swing (swinging ladder mode) 19’ – 26’, maximum swing conventional mode 76’ x 87’. Cat 3406 KITA engine, Murphy EL-150-K1 day tank sender, R.R. 1000DF cutter gear 71,900 in/lb torque, Cutter’s Edge 5 blade left hand 31’ ½ ID, Fairfield reduction gear 8:1 ratio, Pullmaster winches, 12 x 10 dredge pump, well maintained, new paint, new batteries, located East Coast US Price: $410,000
Built 1997, Rebuilt 2012, 64’4” overall length x 18’6” operating width (11’10” transport width) x 4’ hull depth, 30” mean draft, 750 gal fuel capacity, 83,000 lb approx. total dry weight. 3’ minimum digging depth, 18’ maximum digging depth. In-hull mounted dredge pump (new pump shell in 2014), 12” suction x 10” discharge, impeller diameter 32, flow rate 3250 gpm @ 230’. Twin Disc MG5114 marine style reduction gear (new 2018), coupled to an elastomer style coupling 2.54:1 reduction ratio. It could use some steel replacement, special in way of the fuel tanks. Also we had to cut the spuds, and have the bottom portion so will need 2 new spuds – 6” box beam 20 ft long and associated cables. Located Northeast USPrice: $210,000
Built 1980s. 250 cubic yard per hour capacity. 20' depth capacity. Main engine: CAT 3406 diesel. Dimensions: 36' x 12' x 4', with 2'8" draft. Weight: 56,000lb. Fuel capacity: 800 gal. Cutter diameter: 31". Spuds: 12.75” x 29'. Requires refurbishing. Located Northeast.Price: $140,000
2 available, (1) Built 2001 and (1) built 1999 with Cummins Tier 4i engines, 24” diameter auger, 20,000 lb torque, 20’ depth, forward/reverse digging, currently on land, located New YorkPrice: $70,000 each
Built 1993, 4311 hours, 5.9L Cummins 177 hp 6 cylinder engine, 20’ digging depth, 8’ auger head, cable travel with windlass drive, haul trailer with pintle hitch, fittings, hose, anchor plates/stakes, floats and grip pullers. Approximately 2000’ of `10” DHPE pipe with Gheen fittings available. Not used since 2022, currently on land on a trailer, pipe will go on another trailer. It’s in good condition, located in Iowa.Price: $175,000
Built 1989, 5.9 Cummins engine, 10” discharge, well maintained, low hours, cutterhead like new (redone, and not used since), 1500’ of dredge pipe (hard and soft) with floats for some of the pipe, low hours, well maintained, last used 2015 but runs engines periodically, located New YorkPrice: $92,500
Located Hawaii Price: $85,000
12” suction, 10” discharge, 30’ depth, 135” cut length, John Deere SE501687 pump engine, John Deere SE501687 hydraulics engine, cab with a/c Price: $440,000
Built 2019, Overall length (with ladder) 46'. Hull length 30' plus 7' ladder. Overall width: 11.4'. Hull depth: 3.5'. Average draft (with fuel): 2' Aluminum uni-hull design with sealed compartments. Total dry weight: 12 tons. Suction 12", discharge 12". Digging depth: 4' - 15'. Dredge pump engine: International T444E diesel (radiator cooled), 250 HP at 3100RPM. Pump drive: Twin Disc with 10-5V belts with 30"x8" sheaves. Hydraulic cutter: Diameter 36", 60:1 reduction 35 rpm. 4-blade, 12 teeth. Dredge pump: 8" x 10" x 30". Auxiliary water pump: Mission 2"x3". 5-swing hoist hydraulic winches: line pull 8000lbs, 100FPM, 1/2" wire, drum capacity 330'. Hydraulic system: pump: Commercial 37-3 sections, valves: Commercial 35A 7 sections. Capacity: 20 gallons with screens and filter. Fuel capacity: 350 gal (2) removable aluminum fuel cells. Located Kansas. Price: $575,000
Built 2005, 2022 Cat C15 engine, 3’-17’ digging depth, 55’ overall length (with ladder), 17’10” overall width (operational mode), 4’ hull depth, 12’ heigh (less spuds), 38” mean draft (with fuel), 11’11” width (trucking mode), (2) spuds 28’ (1145 lbs) and 30’ (1225 lbs), 70,000 lb total dredge dry weight (approx.).
3’-17’ digging depth,
Swinging ladder - Maximum cut at minimum depth 26’, Maximum cut at maximum depth 19’
Conventional – Maximum cut at minimum depth 80’, Maximum cut at maximum depth 70’
Cat C15 engine, 2828 lb cutting force, 68,000 in/lb operating torque, 88 lb/in cutting force, 28” cutter diameter, 3” shaft diameter, 35 hp cutter rating, 0-32 rpm cutter speed.
Winches: 9617 lb pull (1st layer), 40 ft/min line speed, ½” wire, 208’ drum capacity
Hoist cylinder: 25,535 lb extending force, 41,233 lb retracting force
12” x 10” dredge pump with 32” impeller
Hoist winches: 2204 lb line pull, 81/ft/min, 3/8” wire, 83’ drum capacity
24 VDC battery, 321-645 Delco alternator
800 gal fuel capacity, 150 gal hydraulic oil capacity, operator’s charge, lighted ring buoy, handrails and kick rails, guards, early warning alarm system and engine shut down system, cabin lights, electric bilge pump, replaceable edge cutter, dredge pump priming system, dredge washdown system, high capacity service pump, hydraulic pump/engine clutch disconnect, pump/engine reduction gear, stern pulling eyes,
last used October 2023Price: $525,000
Reworked 2013 / Repowered 1995, Hull rebuilt / refurbished 2014, 65' x 24' x 5', draft 3', 7000 gal fuel capacity. 700 HP CAT 3412 Pump engine, GIW dredge pump, 14" Suction, 12" Discharge. 300 HP Cat 3306 Aux engine, 150 HP Cutterhead drive, 40' Ladder. (2) 16" x 50' stern spuds raised and lowered via winch. (2) 16" x 50' mooring spuds, self-raising and lowering. Hydraulic pumps, motors, cylinders, controls, valves, piping, hoses, and fendering. Firefighting equipment. On blocks, stored on land, excellent condition. Located Northeast USA, in the water. Price: $475,000
50’ max dredging depth, 125’ swing width at minimum dreding depth, 92’ swing width at maximum dredging depth, Cat 3508 engine (1000 hp) Marine Tier 3 (heat exchanger cooled), Cat C9 auxiliary engine (350 hp) Tier 3 (radiator cooled), 1350 hp (not including standard genset), 54” cutter diameter, 29-42 rpm, 7991 lb cutting force, 18” x 66’ spuds, 98’6” overall length with ladder raised, 68’ hull length, 26’ hull width including side pontoons, 4’6” depth, (3) pontoons, ¼” and 5/16” plate thickness of center pontoon, 221,000 lbs dry weight, 2’10” hull draft (not including spuds), 6600 gallon fuel capacity. 7 truckloads.Price: $1,600,000
Detroit 12V92TI diesel engine, mounted on skid, complete, no fuel tank, located FloridaPrice: $65,000
Built 2012. 102' x 23'6", hull depth 5'. Ladder length: 55'. Minimum depth: 6', max depth 44'. Center section: 36' x 11' x 5'. Side pontoons: 90' x 6' x 5'. Dredge pump: Pearce, 18" x 16". Impeller 40" diameter. Main engine: CAT C-32 Acert 1125 HP (4.369 HOURS) with TwinDisc marine transmission. Fuel capacity: 2000 gallons (shared). Aux engine: CAT C-13 ACERT 440HP with Funk hydraulic drive. Cutterhead type: 43" ID, speed 0-20rpm, 150 HP. Winches: (2) Swing: Pullmaster H-18, Ladder hoist: Pullmaster M-25, (2) spuds: Pullmaster H-18. Spuds: 16" x 75' x 7/8" wall thickness. Standard operator cab, 6'8' with A/C and heat. Modified gantry for longer spuds, stainless steel cutter shaft/sleeve. 2-ton jib crane for pump service. Located Northeast US. Price:$1,775,000
20” suction pipe, 20” discharge pipe, 50’ depth, 110’10” L (with ladder raised), 72” hull length x 26’6”W x 7’6” hull depth, 3 pontoons, 4.5’ hull draft (not including spuds), 9000 gal fuel capacity, 335,521 lb dry weight, main engine Cat C32 marine 1300 hp Tier 3 with heat exchanger, Aux engine Cat C15 440 hp tier 3 with heat exchanger, 1740 hp (not including genset), 250 hp at cutter shaft, 54” diameter cutter with 14,900 lb cutting force 18-27-36 rpm. 24” x 66’2” spudsPrice: $2,500,000
55’ dig depth, 70’ Ladder length, 155’ Length x 34’ breadth x 6.75’ depth, 5’ operating draft, main engine EMD 16-645 (2000 hp), 200 HP hydraulic cutter, HPU Cat 3408, (2) 500 kw Cummins KTA 19 Onan AC generator sets, Pullmaster 50 swing winches, Pullmaster 50 ladder winch, Braden 50 ton spud winch, 24” x 50’ spuds, 48,000 gal fuel capacity, fire detection system, to be sold out of USAPrice on Request
Built 2005, reconditioned 2009 and again in 2015, modular design of all welded steel, 133’ x 32’ x 7’ depth, 3.5’ draft (hull only), 170’ overall length, 24 x 24 HHD 62 Georgia Iron Works pump, DC motor G.E. 500 rpm, 3500 HP continuous 700 VDC armature, 9600 DC Digital drive system rated 3500 hp, 600 VAC input, 60 HZ, 72’ ladder plus 20’ extension, 700 hp electric over hydraulic cutterhead, 300 hp jet pump, 36” x 50’ (plus 40’ extensions) spuds hoisted by independent winch with 200 hp AC vector motors, (2) winches with 200 hp AC vector motors with 150,000# pull at 80 fpm. Ladder hoist independent winch powered with 100 hp AC motor. Dredge takes 4160 volt AC power through 3000’ of 8000 volt rated cable spooled on a diesel driven barge mounted reel. Cat 3406 emergency generator set to operate the winches in case of power failure.Was in the process of rebuilding but not completed, new cutterhead and some other parts.Price, as is: $925,000 OBO
105’ x 50’ x 8’, 1965 Bucyrus Erie 88B crane with 12 Cubic Yard clamshell, (2) 30” x 65’ square spuds, (2) H50 Pullmaster winches, 40 KW John Deere generator, set up with weighted spud tension system, set up to dredge 40’+, last worked 2024Price:$2,950,000
Each pontoon has (2) 20 end compartments and 1 10’ center compartment that is a double wall fuel cell with a 500 gallon fuel capacity each pontoon with fill and vent through the deck, each compartment has an 18” round flush mounted access hatch, A-35 ¼” steel hulls with 3” x 3” x ¼” angles spaced 18” apart longitudinal.Price for both: $57,500
Trailer included. Needs new batteries and slight cosmetic work, located GeorgiaPrice: $55,000
Trailer included. Needs work. Located GeorgiaPrice: $19,500
Approximately 2,000 hours. Located FloridaPrice: $200,000
approx. 10,000’ Price: $13 per foot
approx. 5000’ Price: $13 per foot
flanged and ringed HDPE DR17 pipe, located in FloridaPrice on Request
Used 20% wear, approx 3000’ Price: $9 per foot
3,900’ available, 40-50’ sections, located Florida Price: $8 per foot
750’ available, 40-50’ sections, located Florida Price: $12 per foot
24,300 ’ available, 40’-50’ sections, located Florida Price:$15 per foot
Bookmark
Daniel Féau processes personal data in order to optimise communication with our sales leads, our future clients and our established clients.
This site is protected by reCAPTCHA and the Google Privacy Policy and Terms of Service apply.