electronic sump pump switch review

Vertical Slurry Pump | Sump Pump | ICS Wear Group

For Abrasive & High-density Slurries

The Vertical Sump Pump is built for heavy-duty applications requiring reliable, efficient slurry handling. Engineered for industries like mining, aggregates, and chemical processing, these pumps offer long wear life and adaptability to various site conditions.

Recessed impellers with 5 or 8 vanes minimize material degradation, making them ideal for gold processing and delicate applications. Screened inlets and large impeller passages reduce clogging. Cantilever shaft design eliminates lower submerged bearings while the double-suction, semi-open impeller extends wear life and enhances performance. Multiple motor mounting options provide flexible installation for various site conditions. Compact sump size allows for installation in tighter spaces. Top and bottom inlet designs enable operation in “snore” conditions. No gland or submerged bearings means no need for costly gland flush water.

Designed for handling abrasive slurries, including: Mining & Mineral Processing: Gold, Silver, Copper, Zinc, Lead, Nickel, Molybdenum, Lithium, Palladium, Platinum, Rare Earths, Iron, Chrome, Kimberlite, Mineral Sands. Aggregates & Construction: Gravel, Silica Sand, Frac Sand, Limestone, Kaolin, Bauxite/Alumina. Chemical & Industrial Processing: Phosphate, Phosphoric Acid, Chemicals, Acids, Soda Ash, Sugar, Oil, Oil Sands, Biomass. Energy & Power: Coal, Power Generation, Pulp & Paper. Water & Waste Management: Wastewater, Sumps, Slurry, Water with Heavy, Medium, or Light Solids.

Vertical Slurry Pumps Specifications

Up to 25% More Efficient Than the Competition

Sizing: 2 – 8 inch. Heads through 160 ft (50 m). Capacity: The maximum flow rate for the pumps is approximately 800 m3/hr. Shaft Lengths; 900mm – 2100mm pending on model. Pump type: Vertical (submersible). Maximum particle passing size: 12MM for 2-SP (40PV), 45 MM for 6-SP (150SV).

Material: Cr28, Cr30, Cr36,CD4MCu, Rubber & Neoprene. Designed to replace leading OEM pump lines, including SP and SPR. Designed to replace Warman®. High-chrome options available from 28% to 38%, with material recommendations based on abrasiveness, impact, corrosion resistance, and pH levels. ICS offers a range of elastomers, including Neoprene, Viton, Urethane, EPDM, Rubber, Butyl, Nitrile, and specialty compounds. Spare parts available in various alloys, including Ni-Resist (C02), C14 (329 Duplex SS), C21 (420SS), C22 (304 Austenitic SS), C23 (CF8M), C25 (CN-7M SS), C27 (825 Alloy), C29 (904L Austenitic SS), C30 (27Cr 31Ni SS), C43 (431 SS), C44 (440C SS), C55 (Ferralium 255), and C60 (SAF2205 Duplex SS).

Our vertical slurry pumps and parts are ready to ship worldwide from our warehouse, or we can manufacture custom components to your exact specifications.

Slurry Pump Parts Disclaimer

OEM Compatibility Without the OEM Cost

The replacement parts and assemblies provided by ICS Wear Group fit into all all ‘AH’, ‘XU’, ’AHPP’, SP, SPR, and AHFP installations. Any use of competitor names, trademarks, model numbers, item numbers or part numbers is for reference purposes only.

Durco® is a registered trademark of Flowserve Corporation New York USA. Goulds® is a registered trademark of ITT Goulds Pumps Inc., Seneca Falls New York USA. Warman® is a registered trademark of Weir-Minerals Pty. Ltd. Sydney Australia. GIW® is a registered trademark of GIW Industries Georgia USA.

ICS Wear Group supplies vertical slurry pumps and parts to industries worldwide. Whether you need a custom pump or a replacement part, we have you covered. Our components are designed to fit Warman®, Metso®, Millmax®, GIW®, and other OEM pumps.