3 12 inch slurry pump pipe

Hydromatic Pump - Hydromatic HPGFH300M3-4 Submersible Sewage Grinder Pump 3.0 HP 230/460V 3PH Manual 8" imp. 35' cord #HTC515112037

Hydromatic HPGFH Submersible Sewage Grinder Pump Description

Hydromatic HPGFH Submersible Sewage Grinder Pump is designed to meet the demands of Residential, Commercial and Resort Areas.

Hydromatic HPGFH Typical Application

Residential

Commercial

Resort Area

Hydromatic HPGFH Superior Features

One epoxy barrier and one compression fitting for maximum protection against wicking and water seepage into the motor housing.

The heavy-duty ball bearings, upper (radial) and lower (thrust), are continuously lubricated by oil to ensure long service life.

Electrical motor design combines the advantages of high torque output with optimum running efficiency engineered specifically for grinder operation.

The stator is secured to the motor housing by means of stator bolts and retaining ring which ensure ease of maintenance if the need ever arises.

Standard stainless steel shaft in grinder pump

Dual seals for maximum moisture protection.

Moisture detection probe.

Exclusive “Dual Cutter” design cuts solids to smallest particle size, thereby greatly reducing clogging, roping, or binding.

Engineered nonmetallic semiopen impeller molded to a bronze insert for greatest torque driving capabilities. Impeller made of high strength Valox® which provides highest level of corrosion resistance and maximum toughness from impact for a wide variety of slurry pumpage. Pump-out vanes preclude material buildup around shaft and seal.

Hydromatic HPGFH Key Features

Explosion-proof

Class 1, Division 1, Groups C & D

Dual seals for maximum moisture protection

Oil-filled motor for maximum heat dissipation and constant bearing lubrication

Exclusive dual cutter design cuts solids to the smallest particle size

Semi-open impeller provides steep non-overloading operating curve

Available configurations, rails and accessories:

Rail Systems Available

Controls and Accessories Available

Hydromatic HPGFH300M3-4 Technical Details

BODY CONSTRUCTION: Class 30 Cast Iron

HORSEPOWER: 3.0 HP

RPM: 1750

MAXIMUM HEAD: up to 113'

MAXIMUM CAPACITY: up to 50 GPM

DISCHARGE PIPE SIZE: 3" 125# Flange Horizontal Discharge

CORD LENGTH: 35' Standard

CORD SIZE: 14-4; Type: SOOW, W

AMP DRAW (full load): 9.5

VOLTAGE: 3ø, 230/460V

MAXIMUM LIQUID TEMPERATURE: 140°F

MOTOR: Enclosed, Oil Cooled Induction

IMPELLER CONSTRUCTION: Semi-Open 5 Vane, Red Brass #85-5-5-5, ASTM B584-836

IMPELLER SIZE: 8.0"

Hydromatic S3S200M2-4 Submersible Sewage pumps Description

Hydromatic S3S Submersible Sewage pumps are suited to wet-well installation in a wide variety of municipal, industrial and building trades applications.

Hydromatic S3S Typical Application

Municipal Sewage Lift Stations

Industrial Sewage Transfer

Dewatering of Storm Water

Hydromatic S3S Superior Features

Oil-Filled Motor for Cooler Operation, Longer Life, and Less Maintenance. The Dielectric Oil Effectively Dissipates Heat and Lubricates Upper and Lower Ball Bearings.

Single Phase Motors are Capacitor Start, Capacitor Run with Capacitors Located in Control Panel. Contact distributor for Proper Hydromatic Control Panel Sizing.

Standard Construction is Cast Iron.

300 Series Stainless Steel Shafts.

35' Power Cord has Three Conductor PVC Jacket.

Field Serviceable; Pumps have 300 Series Stainless Steel Fasteners for Easy Tear Down.

Semi-Open, Two-Vane Sewage Type Impellers have Pump-Out Vanes on Back Shrouds to Prevent Stringy Materials from Building up Around Shaft and Seal.

Manufactured with Carbon and Ceramic Faced Mechanical Shaft Seal for Long Leak Proof Life.

All Units Given Complete Hydraulic Test Run Before Shipping.