EUR
en
Pumps Mixers Strainers Engineered Systems and Controls Operation and Maintenance Manual TORUS RECESSED IMPELLER PUMP MODELS R, XR, RS PROJECT: EQUIPMENT: MODEL: QUANTITY: SERIAL #: LOCAL REPRESENTATIVE: DATE:
HAYWARD GORDON ULC endeavours to supply equipment of the highest quality both in materials and workmanship. However, within one year from date of startup or eighteen (18) months from date of shipment (whichever comes first) if any part of the equipment manufactured by HAYWARD GORDON ULC is proven to have been defective in material or workmanship, HAYWARD GORDON ULC shall have the right and obligation to promptly repair or replace such part F.O.B its works. Pumps or parts to be considered for warranty repair or replacement must be returned freight prepaid to Hayward Gordon’s factory at Halton Hills, ON. We reserve the right to require the return of defective parts before any claim is recognized. Materials are certified to be of the specified composition, however, the materials are not guaranteed against chemical attack or wear. No other warranty or condition, whether statutory or otherwise, is made, intended or to be implied and, except for its obligation to repair or replace defective parts as provided for above, HAYWARD GORDON ULC will not be responsible for any costs or damages, direct or indirect, which may result to the Purchaser from any defect in the equipment (whether of workmanship, material, design or otherwise) or from any breakage or stoppage thereof. Such costs specifical ly include, but are not limited to, equipment removal, re-inst allation, and freight. In any event, the liability of HAYWARD GORDON ULC arising through the supply of defective equipment shall not exceed the purchase price of the equipment. For equipment included in this unit but manufactured by others, HAYWARD GORDON ULC will endeavor to assign to the purchaser, the guarantee extended by such manufacturers to HAYWARD GORDON ULC.
Before putting pump into service carefully study and adhere to all sections of this manual, as this is necessary for safe and satisfactory operation of your new Hayward Gordon Pump. This pump has components with sharp edges and pinch areas that can cause cuts. Always wear protective gloves when working on or around the pump. Always disconnect electrical power and lock out the motor starter before performing any work on the pump/motor unit. On duplex pumps with alternating relays, both starters must be locked out regardless of which pump is being worked on.
Care must be taken when unloading pump. Unit must be lifted from all four lifting points in each corner of the base. An adequately sized crane or hoist must be used to lift unit. All lifting equipment (i.e., chains, hooks and eyes) must be in accordance with local or federal safety codes. Failure to use approved lifting equipment may result in serious injury.
Inspection should be performed immediately after unloading pump. Examine equipment for broken, cracked, bent or missing parts. Carefully check: 1. Base 2. Motor, pump feet, coupling and flanges 3. Shafts 4. Motor end bells, eyebolts, conduit box. Report all damage or loss to the transportation company and Hayward Gordon.
If the pump is not to be installed and operated shortly after arrival (more than two weeks), sufficient preparation for storage should be made. 1. Inspect pump on skid or open crate if applicable and check for any signs of damage due to shipment. 2. Remove glands, packing and lantern ring from stuffing box. If pu mp is fitted with a mechanical seal, ensure seal faces are dry. 3. Protect exposed steel part s with a r ust p reventative. 4. Cover pump suction, discharge and all opening with masking tape, wood or cardboard. 5. Store pump in a dry location, protected from moisture, dirt, dust, pests and vib rations or ratt les. 6. Cover pump with tar paulin if ar ea has no protective covering. 7. Rotate shaft every week to prevent pitting of be aring surfaces. Monthly inspect ions are recommended. 8. Re-grease motor bearings (if applicable) every six months and rotate t he shaft by hand ev ery week. 9. For pumps with gr ease lubricated bearings, re-grease at six month intervals. 10. For pumps with oil lubricated bearings, remove the vent at the top of the bearing housing and fill the chamber completely with 20W non-det ergent oil which contains rust inhibitors. Replace the vent after filling. Before starting the pump, drain the oil to the r ecommended level and run for two minutes. Stop the pump and drain complete ly of oil. Refill the bearing housing with new oil.
Allow ample space for maintenance a nd inspection. Provide headroom and ventilation in a dry location. Do not locate near dangerous or harmful elements or temperatures. Install as near to liquid source as possible. Use shortest possible direct suction pipe. Keep discharge piping direct with minimum of elbows (long radius preferred) and fittings.
Bookmark
Daniel Féau processes personal data in order to optimise communication with our sales leads, our future clients and our established clients.
This site is protected by reCAPTCHA and the Google Privacy Policy and Terms of Service apply.